Promised Pictures Updated 11-15-07

basketcase0302 · Post by **basketcase0302** » Thu Oct 11, 2007 4:13 pm

70Fordtrk,

Looking good for sure!

My Ranchero has the same Fred Flintstone floorboard on the passenger side!

Basketcase

1970FordTK · Post by **1970FordTK** » Fri Oct 12, 2007 9:22 am

Amazingly the only rusted through spots where the floor pans and the spot behind the chrome trim on the front of the hood. I had enough 18 ga. sheet metal around so that I used it to make the floor pans out of, I will bet it would have been a lot easier to just buy a set of them and weld in. I used the silver POR-15 as you can see in the pictures which I covered with black truck bedliner paint. I wish the last picture (one of just the frame with just the tires attached) could tell the whole story of that day. I used the pressure washer to clean all the oil slick and dirt off the front half of the frame. What it didn't show was that when I went to turn on the water for the pressure washer, was the 5' + long copper head that was between the hose real and the faucet on the house. That was a little bit of excitement I could have done without being that it was 100F outside that day. I would have done the photo bucket deal but I keep getting the "offline and to check back soon line" when I go to it. Hope to get the second roll done soon and post them up for you guys to see.

1970FordTK · Post by **1970FordTK** » Thu Nov 15, 2007 11:53 pm

1970FordTK · Post by **1970FordTK** » Thu Nov 15, 2007 11:55 pm

1970FordTK · Post by **1970FordTK** » Thu Nov 15, 2007 11:57 pm

1970FordTK · Post by **1970FordTK** » Thu Nov 15, 2007 11:58 pm

1970FordTK · Post by **1970FordTK** » Fri Nov 16, 2007 12:00 am

1970FordTK · Post by **1970FordTK** » Fri Nov 16, 2007 12:01 am

1970FordTK · Post by **1970FordTK** » Fri Nov 16, 2007 12:03 am

1970FordTK · Post by **1970FordTK** » Fri Nov 16, 2007 12:05 am

1970FordTK · Post by **1970FordTK** » Fri Nov 16, 2007 12:06 am

1970FordTK · Post by **1970FordTK** » Fri Nov 16, 2007 12:11 am

Like I said before, I'm not the best picture taker but I do know how to get the job done. Now the fun of working the slide hammer on the doors and welding up all the holes. Thanks for looking.

Manny · Post by **Manny** » Thu Nov 22, 2007 8:56 am

From what i can see you do fine with taking, and scanning looks like you take great attention to detail very nice.

1970FordTK · Post by **1970FordTK** » Thu Nov 22, 2007 7:26 pm

Thanks Manny, yours is looking great also. Believe it or not, this will be a work truck when I'm done. One of the fun things I'm doing is filling the holes where the 3 5/8" trim went down it. Somehow I just didn't like it on that truck. Now that the photo galleries are up I've put my pictures there.
http://www.fordification.com/galleries/ ... b_ed51.jpg Hope to see your updates soon, catch you later.

The FORDification.com Forums

Promised Pictures Updated 11-15-07

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures

re: Promised Pictures Updated 11-15-07

re: Promised Pictures Updated 11-15-07

re: Promised Pictures Updated 11-15-07